/* * Copyright (c) 2021 Valentin Milea <valentin.milea@gmail.com> * Copyright (c) 2023 Raspberry Pi (Trading) Ltd. * * SPDX-License-Identifier: BSD-3-Clause */ #include <hardware/i2c.h> #include <pico/i2c_slave.h> #include <pico/stdlib.h> #include <stdio.h> #include <string.h> static const uint I2C_SLAVE_ADDRESS = 0x17; static const uint I2C_BAUDRATE = 100000; // 100 kHz #ifdef i2c_default // For this example, we run both the master and slave from the same board. // You'll need to wire pin GP4 to GP6 (SDA), and pin GP5 to GP7 (SCL). static const uint I2C_SLAVE_SDA_PIN = PICO_DEFAULT_I2C_SDA_PIN; // 4 static const uint I2C_SLAVE_SCL_PIN = PICO_DEFAULT_I2C_SCL_PIN; // 5 static const uint I2C_MASTER_SDA_PIN = 6; static const uint I2C_MASTER_SCL_PIN = 7; // The slave implements a 256 byte memory. To write a series of bytes, the master first // writes the memory address, followed by the data. The address is automatically incremented // for each byte transferred, looping back to 0 upon reaching the end. Reading is done // sequentially from the current memory address. static struct { uint8_t mem[256]; uint8_t mem_address; bool mem_address_written; } context; // Our handler is called from the I2C ISR, so it must complete quickly. Blocking calls / // printing to stdio may interfere with interrupt handling. static void i2c_slave_handler(i2c_inst_t *i2c, i2c_slave_event_t event) { switch (event) { case I2C_SLAVE_RECEIVE: // master has written some data if (!context.mem_address_written) { // writes always start with the memory address context.mem_address = i2c_read_byte_raw(i2c); context.mem_address_written = true; } else { // save into memory context.mem[context.mem_address] = i2c_read_byte_raw(i2c); context.mem_address++; } break; case I2C_SLAVE_REQUEST: // master is requesting data // load from memory i2c_write_byte_raw(i2c, context.mem[context.mem_address]); context.mem_address++; break; case I2C_SLAVE_FINISH: // master has signalled Stop / Restart context.mem_address_written = false; break; default: break; } } static void setup_slave() { gpio_init(I2C_SLAVE_SDA_PIN); gpio_set_function(I2C_SLAVE_SDA_PIN, GPIO_FUNC_I2C); gpio_pull_up(I2C_SLAVE_SDA_PIN); gpio_init(I2C_SLAVE_SCL_PIN); gpio_set_function(I2C_SLAVE_SCL_PIN, GPIO_FUNC_I2C); gpio_pull_up(I2C_SLAVE_SCL_PIN); i2c_init(i2c0, I2C_BAUDRATE); // configure I2C0 for slave mode i2c_slave_init(i2c0, I2C_SLAVE_ADDRESS, &i2c_slave_handler); } static void run_master() { gpio_init(I2C_MASTER_SDA_PIN); gpio_set_function(I2C_MASTER_SDA_PIN, GPIO_FUNC_I2C); // pull-ups are already active on slave side, this is just a fail-safe in case the wiring is faulty gpio_pull_up(I2C_MASTER_SDA_PIN); gpio_init(I2C_MASTER_SCL_PIN); gpio_set_function(I2C_MASTER_SCL_PIN, GPIO_FUNC_I2C); gpio_pull_up(I2C_MASTER_SCL_PIN); i2c_init(i2c1, I2C_BAUDRATE); for (uint8_t mem_address = 0;; mem_address = (mem_address + 32) % 256) { char msg[32]; snprintf(msg, sizeof(msg), "Hello, I2C slave! - 0x%02X", mem_address); uint8_t msg_len = strlen(msg); uint8_t buf[32]; buf[0] = mem_address; memcpy(buf + 1, msg, msg_len); // write message at mem_address printf("Write at 0x%02X: '%s'\n", mem_address, msg); int count = i2c_write_blocking(i2c1, I2C_SLAVE_ADDRESS, buf, 1 + msg_len, false); if (count < 0) { puts("Couldn't write to slave, please check your wiring!"); return; } hard_assert(count == 1 + msg_len); // seek to mem_address count = i2c_write_blocking(i2c1, I2C_SLAVE_ADDRESS, buf, 1, true); hard_assert(count == 1); // partial read uint8_t split = 5; count = i2c_read_blocking(i2c1, I2C_SLAVE_ADDRESS, buf, split, true); hard_assert(count == split); buf[count] = '\0'; printf("Read at 0x%02X: '%s'\n", mem_address, buf); hard_assert(memcmp(buf, msg, split) == 0); // read the remaining bytes, continuing from last address count = i2c_read_blocking(i2c1, I2C_SLAVE_ADDRESS, buf, msg_len - split, false); hard_assert(count == msg_len - split); buf[count] = '\0'; printf("Read at 0x%02X: '%s'\n", mem_address + split, buf); hard_assert(memcmp(buf, msg + split, msg_len - split) == 0); puts(""); sleep_ms(2000); } } #endif int main() { stdio_init_all(); #if !defined(i2c_default) || !defined(PICO_DEFAULT_I2C_SDA_PIN) || !defined(PICO_DEFAULT_I2C_SCL_PIN) #warning i2c / slave_mem_i2c example requires a board with I2C pins puts("Default I2C pins were not defined"); return 0; #else puts("\nI2C slave example"); setup_slave(); run_master(); #endif }

This firmware image was imported from the pico-examples repository. 


Copyright 2020 (c) 2020 Raspberry Pi (Trading) Ltd.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following
   disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following
   disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products
   derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.